Onhlp.com
The F0E1 Error Code indicates that you are trying to run a "Clean Washer" cycle and the washer is detecting there are items still in the washer/dryer.
Remove load and restart the Clean Washer with affresh®cycle.
The F0E2 Error Code indicates that there are excessive suds detected inside the washer/dryer.
The washer/dryer is running a suds reduction routine in order to reduce the amount of suds. Allow the cycle to continue.
Use only HE (high efficiency) detergent in this washer/dryer.
The F0E3 error code indicates that the temperatures in the washer/dryer are too hot during the dry cycle. Verify that you are using the right cycle for the fabrics being laundered.
Try resetting the washer/dryer by unplugging it from the outletfor at least 1 minute and then plugging it back in. If unsuccessful, call for service.
An F0E4 Error Code indicates that the wash water temperature is too hot. The washer/dryer may be connectedincorrectly to the home water supply.
The washer/dryer must be connected tocold water. Verifythat the unit is connected to the coldwater supply only.
See installation instructions for further information on connecting to the water supply.
The F0E5 Error code indicates that an off balance load has been detected. This means that the load in the washer/dryer could be too large, or it could be unbalanced.
Avoid tightly packing the washer/dryer. Avoid washing singleitems. Balance a single itemsuch as a rug or jeans with a
few extra items.
Note that an unbalanced load may not reach the intended washer spin speed for the cycle you selected. This could increase dry times.
The F1E4 Error Code indicates there may be a problem with the main relay.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute and then plugging it back in. If unsuccessful, call for service.
The F3E1 Error Code indicates that there may be aproblem with the Water Pressure sensor. Verify that your water supply has the adequate amount of pressure going to the washer/dryer.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute and then plugging it back in. You may need to run a drain only cycle if there is still water in the Washer/Dryer. If unsuccessful, call for service.
The F3E2 Error Code indicates that there may be an issue with the Temperature Control sensor.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F3E3Error Code indicates that there may be an issue with the Air Inlet function. The wash function will operate, but the dry function will not operate.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F3E4Error Code indicates that there may be an issue with the sensor detecting the detergent level in the Load & Go™ Dispenser.
A potential cause of this Error Code is a clog in the dispenser.Clean the Load & Go™ bulk detergent dispenser,or add detergent manually until dispenser is cleaned. If you have questions about how to clean yourLoad & Go™ bulk detergent dispenser, see the "Cleaning and Maintenance" section of this Troubleshooting Guide, or review your Use & Care Guide.
The F4E2Error Code indicates that there may be an issue with the dryer heater circuit. The wash function will operate, but the dry function will not operate.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F4E3Error Code indicates that there may be an issue with the dryer blower motor. The wash function will operate, but the dry function will not operate.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F5E1Error Code indicates that there may be an issue with the doorswitch/door lock. The door is unlockedduring a cycle when it should belocked.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F5E2Error Code indicates that there may be an issue with the doorlock.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F5E3Error Code indicates that there may be an issue with the doorlock.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F5E4Error Code indicates that the washer/dryer door has not been opened between cycles. Three consecutive cycles were runwithout the door being opened. Thewasher/dryer will generate an invalidkey beep when START is pressed.
Open and close the door. Check for obstructions around thedoor switch and latch.Verify functionality of door switch by opening and closing the door.
For best results, removing clothing promptly once cycle has completed.
The F6E1Error Code indicates that there may be a communication failure between the electronics in the washer/dryer.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F6E2Error Code indicates that there may be a communication failure between the electronics in the washer/dryer.
Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
The F8E1Error Code indicates that the washer/dryer is not detecting any water flow going to the washer/dryer. This can be caused by several reasons, including the following:
Make sure that the washer/dryer is connected to the homecold water supply, and that the home water supply valve is fully open (turned on). Verify that the inlet hose to the washer/dryer is notkinked. If problem persists, call for service.
The F8E3 Error Code indicates that there may be an internal overflow from the water inlet valve.
Verify thatthe drain hose and drain pump filter are not plugged. See Cleaning and Maintenance section above for more information.
If this does not resolve the issue, call for service.
The F9E1Error Code indicates that the washer/dryer is not draining in a timely manner, or at all.This could be due to the following:
Clean the drain pump filter and the bellows drain holes(see Cleaning and Maintenance symptom above).
Check the drain hose for obstructions and verify installation. The drain hose cannot be more than 4.5 inches into the stand pipe or laundry sink. It also must be routed at least 24 inches from the floor, and not over 96 inches. See the installation instructions for more details of installing the drain hose.
Published: Saturday, April 11, 2020 Viewed
183 times.
Ask me about:
The F-01 error code indicates a primary control board failure on this model of dryer. If the error cleared after unplugging it for 20-30, then the control board could have received a power surge or glitch through the electrical lines.
Yes, there is a reset procedure to fix this. The Whirlpool Cabrio washers need to be reset in a different method than many other types and brands of washers. Here is how you can RESET your Cabrio washer (all Whirlpool Cabrio models). Follow the directions below and your washer should reset and begin to work normally.
Pull down on the bottom panel and pull it away from the washer. Reach through the open panel and up to the door lock. Find the release ring below the locking mechanism. Pull down on the ring to unlock the door.
The F01 error code means the primary control unit in the dryer has failed and will have to be replaced. The control that needs replacing is the electronic control board not the user interface and/or control panel.
Learn how to reset the settings on your Frigidaire dishwasher to solve performance issues and get it back to optimal working condition.
Resetting Frigidaire dishwasher settings Answers: 0 42
Learn how to properly restart a Whirlpool washer that stops mid-cycle due to a power outage or another issue. Follow these steps for a seamless reset.
Whirlpool washer restart procedure Answers: 0 45
The Dyson vacuum's battery typically lasts around 3-5 years before needing to be replaced, depending on usage and maintenance.
Dyson vacuum battery longevity Answers: 0 54
Learn how to troubleshoot and solve water inlet issues on a GE dishwasher with common steps and tips to ensure your appliance functions properly.
Solving water inlet issue on GE dishwasher Answers: 0 52
Learn how to troubleshoot and diagnose error codes on your Asko washer with helpful guidance and step-by-step instructions. Get your appliance back up and running in no time!
Asko washer error code diagnosis Answers: 0 34
The thermal fuse in a GE dishwasher acts as a safety measure by cutting off power if the temperature exceeds a certain limit, preventing overheating and ensuring safe operation.
Thermal fuse safety in GE dishwasher Answers: 0 36
Learn how to reset the control lock on your Frigidaire dishwasher when the buttons are unresponsive with simple step-by-step instructions.
Frigidaire dishwasher control lock reset Answers: 0 47
Learn how to properly restart a Frigidaire dishwasher that has stopped mid-cycle with simple steps and troubleshooting tips to get it working again.
How to restart Frigidaire dishwasher Answers: 0 47
Learn how to troubleshoot and fix water inlet issues on your GE dishwasher to ensure it runs smoothly. Follow these tips to keep your dishwasher working efficiently.
Solving water inlet issue on GE dishwasher Answers: 0 31
Learn how to quickly reset your Samsung washer to troubleshoot and resolve any issues or errors in a few simple steps to get it back up and running smoothly.
Samsung washer quick reset Answers: 0 30
Learn how to troubleshoot and restart your Samsung washing machine when it unexpectedly stops mid-cycle. Get your laundry back on track with these helpful tips.
Restart Samsung washing machine Answers: 0 20
Learn how to reset your Whirlpool washer to its factory settings and understand the impact it can have on the machine's performance. Proper maintenance is key for optimal functioning.
Whirlpool washer factory settings restore Answers: 0 18
Learn how to troubleshoot and properly restart your Samsung washing machine if it suddenly stops mid-cycle. Follow these steps to get your machine back up and running smoothly.
Restart Samsung washing machine Answers: 0 19
Learn how to troubleshoot water inlet issues on your GE dishwasher to ensure it is functioning properly. Follow these steps to identify and resolve any problems.
Troubleshooting GE dishwasher water inlet Answers: 0 18
Learn the steps to clear the memory on your Whirlpool washer to fix error codes and reset settings. Keep your appliance running smoothly with our simple guide.
Clearing memory on Whirlpool washer Answers: 0 24
onhlp.com: Your Questions and Answers Resource with a Wealth of General Knowledge
Are you seeking a one-stop destination for comprehensive knowledge and answers to your burning questions? Look no further than onhlp.com! Our platform is your go-to source for a wide range of information, all conveniently presented in an easily accessible question and answer format.
At onhlp.com, we pride ourselves on being your reliable knowledge hub. Whether you're curious about technology, science, history, or any other subject under the sun, our extensive General Knowledge (GK) knowledge base has you covered. We've made it our mission to provide you with in-depth insights and facts on an array of topics. Read more
